The ring in the photo is 150# test, magnified about 10X.  There is no need to mention the brand name because you have no choice in who's ring you get when you buy a lure.  Just for the heck of it, pick up a lure with the largest split ring you can find and run your finger across the end of the ring.  You might be surprised.  A magnifying glass will reveal even more.  Imagine what those sharp ends can do to mono if you use a loop knot that slides back and forth across them.   I checked 3 brands of split rings and all were rough to sharp.  I darn sure won't be using a Loop Knot with split rings anymore.  

I've reeled in an empty line to find a loop that was frayed into in the middle more than once.  "Damned Spanish Mackerel" has often been my thought.  Last week it happened to me on Lake Rousseau where there are absolutely no Spanish.  I looked at my knot very carefully then clipped it off, bagged it and brought it home to look at magnified.  The "Old light bulb" flickered then came on at full power.

Here is the frayed knot I clipped and saved.  Photo quality isn't great but you should see it at 20X under a steroscope, properly lighted.

A snap will eliminate the problem but there may be another problem we haven't talked about here yet. 

Did you ever see a split ring that was slightly open?  They sometimes spring open under heavy strain but I've seen deformed rings on new lures; rings that were deformed by installation.  I found the lure I used to illustrate my point floating in lake Rousseau, the same day I made the above observation.  There was no knot on the ring but that doesn't totally support this next argument.  Small wire slips out of a split ring even easier.

I tied this Loop Knot and photographed it after slipping it through the deformed split ring above.  The leader in both cases is 20# Berkley Vanish Fluorocarbon.

Now lets tie a knot that will eliminate this problem, once and for all.

For lack of a better name, I call this knot the "Split-Ring Knot."  Tie it on the side away from the split and you will never have a problem because it will not slip, come un-tied or slide around on the ring.

To tie the "Split-Ring Knot, pass the leader through the ring, through the ring a 2nd time, around to the other side of the standing end and back through the ring a third time.  Pass the bitter end around the standing end twice and back through all 3 loops.  Moisten and tighten.

I used single strand electrical wire for the first 4 steps and 50# test Shakespeare Cajun mono for the final completed knot.  It is difficult to tie the "Split Ring Knot" with stiff mono. 

Here is the "Split Ring Knot" tied  step by step

A little better look at the completed Split Ring Knot.

That's all.

Life is too short to catch little fish.

 http://www.panhandlefishingbooks.com/

I spent an hour this morning looking for the envelope where stored the frayed through loop I mentioned in the tip above.  Now I have to photograph it for the tip. 

A lot of time and effort goes into many of these tips.

Watch the tip above as it grows.

Life is too short to catch little fish.

 http://www.panhandlefishingbooks.com/

I followed your narrative of how to tie your "split ring knot" but I am missing something or don't understand everything you said. I don't see the 2 wraps around the standing end on your photo?? It looks, after the crossover and the third loop through the split ring, that the bitter end went around the standing end one time and then under all 3 loops. Am I missing something or did I read the steps wrong??

Thanks again for your very informative hints and tips on fishing and kayak rigging. I have learned much from reading your posts and I have paddled for over 50 years which makes some people "experts" by default!! Me? I am still a student of most everything that I do and have done in my life and I continue to learn more and more from guys like you.

Keep up the good posts and ideas!!

 

Ok, here is what happened.  I tied the illustration with the stiffest 50# test I have ever used and couldn't make the 2 or 3 wraps.  With up to 20 or 30#, three loops are easy enough.  I couldn't pull the knot tight with 3 wraps.

Sort of a "Rule of thumb" to use when knot tying, use fewer wraps with stiffer line because you will not be able to cinch the knot down with many wraps.

I'll add photos illustrating the complete process tomorrow.

The real beauty of this knot is that it doesn't slip around the ring like some knots do.  The Palomar works ok too but it difficult to tie with long lures.

Life is too short to catch little fish.

 http://www.panhandlefishingbooks.com/

 http://www.panhandlefishingbooks.com/

I always use a snap or snap swivel to a split ring. I use a short section of wire to a solid ring (LB Huntington Drone here)

Loop knot to Uni to Uni -

Honestly, I am sure this doesn't happen often or somebody would have come up with a sure cure.

OK, the "Ole Lightbulb" just came on.  I wonder if a little J-B Weld on the ring would cure the problem?  I love J-B Weld.

Life is too short to catch little fish.

 http://www.panhandlefishingbooks.com/

I have just never tied a loop or directly to a split ring with anything but wire.

I pay the price for the ball bearing snap swivel to avoid such cut offs. 

Let us know about the JB Weld.

Thanks

 http://www.panhandlefishingbooks.com/

While I doubt if it added anything much to strength, I am sure it would keep wire from slipping down into the split and help prevent fraying of a loop knot in mono.

Lets just call this "Better than nothing."

Life is too short to catch little fish.

 http://www.panhandlefishingbooks.com/

Wade B.

Mako 284 w/ twin 250 verados

Wade B.

Mako 284 w/ twin 250 verados

I have some "King spoons" that come with split rings that I can compare. It looks like the weather will permit an offshore trip later this week.